| |
|
|
Sealing
& Maintenance Products
-
Clean
and sparkle: A neutral cleaner suitable for all surfaces
for routine cleaning.
-
Tile
and porcelain cleaner: A slightly acidic cleanser for
deeper cleaning just before refinishing.
-
Tile
treat: A neutralizing rinse to remove efflorescence
and alkaline residue.
-
458
Wax off: A water-soluble stripper to remove old wax
build-ups. For professional use only.
-
Enriching
Oil: A coloring oil to enhance the color of porous
tile providing it has not been previously sealed or has a glazed
finish.
-
Clay
Sealer: A water based clay sealer to protect clay tile
pavers that also requires a topical liquid finish coating.
-
Super
to the Point Finish: A topical liquid finish coating
with a high gloss sheen. It is designed to be the wear coat
on a finished, interior tile floor. It also has a low sheen
version: Super to the Point Flat.
-
Grout
Eze: A type of pre seal to apply just prior to grouting
to allow for easier grouting and to avoid cement stains on the
tile being grouted that can occur during the grouting procedure.
-
Preservit:
non-shining, penetrating sealer for all porous surfaces that
repels water and most oils.
-
Stone
Guard: An upgrade, non-shining, penetrating sealer
for all porous surfaces that repels water and most oils
-
Pen
Seal: an economical water repellent for unglazed tile,
stone and grout.
-
Multi
Set Thinset: A polymer modified mortar designed for
bonding ceramic tile, stone tile and porcelain tile to floors
and walls. It features high bond strength and excellent workability.
For vitreous and semi-vitreous tile. Meets or exceeds ANSI-A-118.4
and ANSI-A-118.11.
-
Modified
Porcelain Flexible Thinset: The highest grade polymer-modified
thinset designed for installation of porcelain tiles over difficult
to bond to substance like exterior grade plywood, vinyl tile
and cutback adhesive residue. For vitreous and semi-vitreous
tile. Meets or exceeds ANSI-A-118.4 and ANSI-A-118.11.
-
White
Stone Set: Stone set mortar is a single component,
high performance; polymer modified thin suet mortar, which is
mixed with water only. Stone Set Mortar is specifically designed
for bonding ceramic tile, porcelain tile and natural stone to
difficult to bond substrates such as exterior grade plywood
vinyl tile, cutback adhesives, etc. Exceeds ANSI-A-118.11.
-
Medium
Bed Modified: Medium Bed Modified is a dry set mortar
modified with a unique blend of chemical additives. It may be
used for both interior and exterior applications and is perfect
for the installation of 16x16 or larger, uneven tiles. Excellent
non-sag properties allow for both wall and floor applications.
Medium Bed Modified can be used for setting absorptive, semi-vitreous
and vitreous tiles on a mortar bed up to ¾” thick.
-
Aqua
Seal: Aqua Seal is a premium ready to use waterproofing
and anti fracture membrane. Ideal for a variety of residential
and commercial applications, Aqua Seal can be installed on floors
exposed to heavy water usage, structures designed to hold water
permanently and all floor penetrations where water leakage is
a concern. As an anti-fracture
-
Flex-Guard:
Flex-Guard Crack Isolation System is a two component,
primer less, pressure sensitive, elastomeric, crack isolation,
and anti fracture system. The top layer consists of a polyester
stitch fabric, which is laminated with an adhesive. The adhesive
is a solvent free, 100% solids, modified acrylic adhesive.
-
Wonderboard:
½” Wonderboard is a glass mesh reinforced cement
backer board. Remains stable while increasing in strength, even
when exposed to continuous moisture, reducing potential damage
from moisture penetration. Matches up with surrounding ½”
drywall installations without the need to use shims or spacers
on wall studs. Tapeless installation on open mesh edges provides
superior edge bond strength. Easy to score, snap, cutout and
nail. Protected by MoldGard technology to resist mold and mildew.
- Wall
Float: A preblended plaster mix designed specifically
for tile contractors to improve labor efficiency and easier handling
in difficult access areas. It can be used as a leveling coat over
tile lath or concrete masonry for tile, brick and veneer installations.
Wall Float is a blend of Portland Cement. Type S Lime and washed
and graded plaster sand. For walls and ceilings only both interior
and exterior. Requires only the addition of water.
- Deck
Mud:
Designed specifically for the tile setting contractor to increase
labor efficiency and easier handling in difficult access areas.
It can be used as a leveling mortar for interior or exterior underlayment.Deck
Mud is a mixture of graded plaster sand meeting ASTM C 144 Specification
and Portland Cement Type I-II-V that conforms to ASTM C - 150.
Requires only the addition of water.
-
Saltillo
Grout: PaverMix is a grouting compound designed for
joints 1/2" to 1" (12.7 to 25.4 mm) usually associated
with terra cotta tile, such as Mexican, Brazilian and Spanish
tile. PaverMix is a blend of Portland cement, specially graded
silica sand and chemical additives that form a dense matrix,
free from any voids. It offers ease of cleanup, high compressive
strengths and low shrinkage.
-
MP
Sanded 924 Grout: MP Sanded is a one-part, Latex-Portland
cement grout that provides the user the highest performance
available in the industry, in an easy to use, just-add-water
material. Its unique blend of Portland cement, specially graded
silica fillers, latex modifiers and colorfast pigments produce
a superior grout with excellent flexural and bond strengths,
color control, minimal efflorescence and high comprehensive
strength. MP Sanded is designed for tile installations that
will be subjected to thermal shock. It resists bacteria, fungus,
alkalies and does not shrink or dust.
-
Color
Matching Caulking: Fills and repairs joints around
sinks, tubs, showers and countertops. Can be used instead of
grout to fill tile joints at the junction where tiles change
plane, where a tile abuts other surfaces and where tile is set
over different surfaces. Can also be used to seal windows, door
frames, plywood siding, vinyl and drywall. Maximum joint width
and depth should not exceed ¼”. Not for constant
water exposure. Available in a variety of colors.
|
|
